Skip to content

Health, safety & environment: near-misses by area, ETP against permit

The HSE agent works from your incident register, ETP lab log, fire-drill log, PPE register and SDS files. It counts from the rows you upload and cites its documents. Any email or message it drafts waits for an admin to approve or decline.

Works from: Risk assessment, PPE register, Fire-drill log, Incident report and near-miss log

Four HSE records that fail when an auditor or regulator asks

HSE work runs on registers: the incident book, the ETP lab log, the chemical inventory, the fire-drill log. When one is thin, the cost comes as an injury nobody learned from, a pollution fine or a finding in the buyer’s audit.

  • Near-misses that never reach the register, and CAPAs left open

    A first-aid case goes into a paper book. A near-miss stays in a supervisor’s WhatsApp, or nowhere. Investigations start late, and CAPAs have no owner or due date. The playbook asks for every incident to be classified and investigated within 24 hours, and every near-miss logged. The HSE manager faces the buyer’s auditor with a register that shows the injuries but not the near-misses before them.

    57%

    Share of Better Work Bangladesh factories, in a panel of 65 followed since 2014, still non-compliant in the OSH management-system area in 2022. Its questions include a functioning safety committee and proper recording of accidents.

    Source: International Labour Organization (Better Work Bangladesh), The impact of Better Work Bangladesh: Legacy through a decade (2014–2023) (opens in a new tab), 2024.

  • ETP discharge that drifts, and no record of the days outside the permit

    The ETP chemist writes pH, BOD, COD, TSS, TDS and colour in a log book or a loose Excel file. The monthly third-party test arrives as a PDF, and so does the twice-yearly ZDHC ClearStream report. When the regulator or a buyer asks how many days the plant ran outside its limits, nobody can answer from one place. The environment officer rebuilds the record by hand, and the owner risks a fine or a closure order.

    30%

    Share of 22 Bangladeshi dyeing and wet-processing factories, visited in 2016, that exceeded the DoE’s TDS discharge standard (2,100 mg/L) at their last ETP inspection, as staff reported. pH and TSS were within limits at all 22.

    Source: Transparency International Bangladesh (Bangladesh Water Integrity Network), Use and Effectiveness of Effluent Treatment Plants (ETPs) in the Garments Industry of Bangladesh: a Water Sector Integrity Perspective (opens in a new tab), 2017.

  • Chemicals that pass the gate without an SDS or a ZDHC check

    Dyes and auxiliaries arrive with a lot number but no current SDS, or go into use before anyone checks them against the ZDHC MRSL. The chemical inventory in the store and the approved list in the HSE office drift apart. The worker at the station has no SDS to read after a splash, and the buyer’s chemical team asks why a product off the approved list was in use.

    42%

    Share of 57 garment factories assessed by Better Work Egypt in 2022 that were non-compliant on chemical safety data sheets. Most had SDS files, but some part of a sheet was missing or incorrect.

    Source: Better Work (ILO and IFC), Better Work Egypt Annual Report 2023: An Industry and Compliance Review (opens in a new tab), 2023.

  • Fire drills, extinguisher checks and exits kept on paper

    Drills happen, but the log does not record the zone, the evacuation time or the gaps. Extinguisher checks are ticks on a wall card. Stock blocks an exit, and welding starts without a hot-work permit. The playbook calls for a drill in every zone each quarter, with everyone at the assembly point within four minutes. The HSE manager answers for the gaps at the buyer’s audit, and upper-floor workers carry the risk.

    36%

    Share of garment factories assessed by Better Work in Bangladesh that had obstructed fire exits, in data collected during 2019. In Vietnam the share was 26%.

    Source: Better Work (ILO and IFC), Global Pandemic Highlights the Need for Ongoing Focus on Factory Working Conditions (opens in a new tab), 2020.

Incidents, ETP readings and SDS files, counted and read

It reads what your HSE (EHS) team keeps in files and Google Sheets, not the ETP, the fire panel or the floor. Each count shows the register rows behind it, and any email to a supplier or message to a fire warden waits for an admin to approve or decline.

  • Incidents and near-misses, counted from your register

    Answers with sources

    Upload the incident register or near-miss log as Excel or CSV, with area, class and month or quarter columns. Ask how many near-misses the dye house logged this quarter, or how many lost-time incidents last month, and the agent counts them from the rows and lists the rows it used. Name a few areas and it counts each. Beside the count it quotes the playbook: zero near-misses means under-reporting, not a safe area.

    Ask“How many near-misses did the dye house log this quarter? Show me the rows.”

  • The ETP log compared with your discharge permit

    Answers with sources

    Upload the ETP lab log as a CSV, or an Excel file with the log on its first sheet, with a month column. Ask for figures such as the month’s highest COD, highest and lowest pH and average TDS, and the agent works out each from the rows and compares it with your uploaded permit’s limit, citing both. BOD, TSS and colour work the same way. It reads the log as your chemist recorded it; it is not connected to the ETP.

    Ask“What were the highest COD and the highest and lowest pH in this month’s ETP log, and how do they compare with our permit limits?”

  • SDS and ZDHC status, read from the files on record

    Reads your documents

    Upload your SDS files, the approved chemical list and the monthly InCheck report from the ZDHC Gateway. Ask about a chemical and the agent quotes its hazard class, PPE and first-aid steps from the SDS, and its status in the InCheck report, citing each file. If your chemical inventory has an approved column, it counts the chemicals marked not approved and cites the rows it finds. If no SDS is on file, it says so.

    Ask“What PPE and first-aid steps does the SDS for our reactive fixing agent give, and is it on the approved list?”

  • The monthly HSE report, built from the registers on record

    Creates files

    Ask for the month’s HSE status and the agent sets it out as a document in the playbook’s order: incidents, near-misses, fire drills, PPE audits and ETP. Ask for each figure you want in it, such as the month’s lost-time incidents or zone C’s longest evacuation time, and it works it out from your uploaded register’s rows, citing the file. A missing or unreadable register is named as missing. Every revision is kept.

    Ask“Start the October HSE status summary, beginning with the lost-time incidents the register records for October.”

  • Drill gaps by zone, sent to the fire wardens

    Acts in your tools

    Upload the fire-drill log as Excel or CSV, with zone and year columns. Ask how many drills zone C ran this year, or its longest evacuation time, and the agent works it out from the rows, against the playbook’s four minutes. Ask, and it drafts a WhatsApp or Slack message to that zone’s fire wardens on the gaps the log records. The HSE head, as department admin, approves or declines it, and it is sent only if approved.

    Ask“What was zone C’s longest evacuation time this year? Draft a WhatsApp to the zone C fire wardens with the gaps the log recorded.”

A committee meeting, a COD spike and an audit two weeks out

  • The night before the safety committee

    Safety officer

    The safety committee meets tomorrow, and the chair wants last month’s incidents and every open CAPA.

    1. Asks

      “From the incident register, how many first-aid cases, lost-time incidents and near-misses did the dye house, cutting and the boiler house each log last month? Then list the CAPAs still marked open, with owner and due date.”

    2. The agent

      Reads the incident register uploaded to HSE and counts last month’s first-aid cases, lost-time incidents and near-misses for each of the three areas from the rows, and sets the counts side by side. Reads out the CAPAs it finds marked open, with owner and due date, and builds a one-page sheet for the committee that cites the rows. Where an area’s counts show incidents but no near-misses, it quotes the playbook: that pattern reads as under-reporting.

    3. Result

      The committee works from counts anyone can check against the register, and asks why some areas report almost nothing.

  • A COD reading above the permit

    Environment officer

    The morning ETP sample reads COD above the permit limit, and the chemist has diverted discharge to the balance tank.

    1. Asks

      “COD is over our permit today. Show the last 14 days of the ETP log against the limit, write the deviation note, and draft an email to our lab for a re-test.”

    2. The agent

      Reads the ETP lab log in your Google Sheet and cites the last 14 days of rows beside the COD limit in your uploaded permit. Writes the deviation note as a document: what the log records, the playbook’s steps (stop discharge, divert, treat, re-test, resume only within limits) and what is not yet recorded. Prepares an email through Gmail or Outlook asking your third-party lab for a re-test.

    3. Approval

      The email waits for the HSE head, as department admin, who approves or declines it. It goes to the lab only if approved. Whether to report the deviation to the regulator stays the HSE head’s decision, under your own SOP.

    4. Result

      A deviation note with the log rows behind it, and a re-test request that leaves only if approved. Asked which dyeing batch caused the spike, the agent says Dyeing & Processing owns that.

  • Two weeks before the buyer’s audit

    HSE manager

    The buyer’s audit is in two weeks, and the auditor will go through the HSE checklist line by line.

    1. Asks

      “Build our pre-audit checklist as a sheet. For each line, show the document that proves it and its date, or say it is missing.”

    2. The agent

      Builds the playbook’s pre-audit checklist as a spreadsheet: risk assessments current, PPE issuance tracked, fire-drill logs current, incident log and CAPAs closed, ETP daily log clean, ZDHC MRSL conformance verified. Against each line it names the uploaded document and the date it records, or writes “not found in connected data”. A register uploaded only as a scan has no text to read, so its line shows as not found.

    3. Result

      A list of the gaps two weeks before the auditor finds them, with the document and date behind every line that holds.

What a missed near-miss and an ETP breach cost

The figures below come from Singapore’s WSH Council, the ILO’s Better Work programme and research on Bangladesh’s textile industry, each cited at its source. They are not Mavick results. A pilot records your own HSE KPIs first, then measures them again.

  • Near-misses counted, so the quiet areas stand out

    1:29:300

    Heinrich’s ratio of major injuries to minor injuries to near misses, a cross-industry rule of thumb cited by Singapore’s WSH Council. Other studies found other ratios, but near misses always outnumber accidents.

    How the agent helps

    The agent does not collect reports from the floor. Once near-misses are logged in an Excel or CSV file you upload, it counts them from the rows for an area, a shift or a type you name, so area by area you see which ones rarely report. If you ask, it also writes a toolbox-talk note on a near-miss for the next shift, and sets out the investigation report in the playbook’s order.

    Track: Near-miss reports per month, by area

    Source: Workplace Safety and Health Council, Singapore (with the Ministry of Manpower), Guide to Near Miss Reporting (opens in a new tab), 2016.

  • ETP discharge you can prove stayed inside the permit

    BDT 1,965,000

    Mean Department of Environment fine across 290 water-pollution penalty records in Bangladesh, 2011–2016, 255 for textile factories, about US$24,600 at the paper’s rate. The largest was BDT 30,000,000. Compiled from news reports.

    How the agent helps

    The agent does not treat effluent and is not connected to the plant. When you ask, it works out each named parameter’s monthly average, highest or lowest value from the uploaded log and compares it with your permit. It sets the figures you ask for in the month’s environmental summary, beside the third-party results, so the HSE head sees the highest readings and their rows.

    Track: ETP discharge conformance %, by parameter and month

    Source: Sustainability (MDPI), Water Pollution and the Textile Industry in Bangladesh: Flawed Corporate Practices or Restrictive Opportunities? (opens in a new tab), 2019.

  • PPE checked in use, not only on the issue register

    65%

    Share of 57 garment factories assessed by Better Work Egypt in 2022 that were non-compliant on training and encouraging workers to use PPE and machines properly. 33% were non-compliant on providing the PPE.

    How the agent helps

    The agent does not observe the floor. From an uploaded shop-floor audit sheet with a worn or not-worn column, it works out PPE compliance % for a section you name from the rows. From the PPE register it reads out the items it finds issued and due for replacement. It follows the playbook’s split: a usage gap calls for re-training, an issuance gap for a stock check.

    Track: PPE compliance % on shop-floor audits, by section

    Source: Better Work (ILO and IFC), Better Work Egypt Annual Report 2023: An Industry and Compliance Review (opens in a new tab), 2023.

What to baseline before a pilot

Measure each one before the pilot starts, then again at its end.

Health, Safety & Environment: the KPIs to baseline before a pilot, and why each matters
KPI to baselineWhy it matters
Lost-time incident rate (LTIR)The playbook’s target is zero. The rate needs hours worked, which HR holds, so HSE needs its own copy of the hours for the agent to use.
Near-miss reports per month, by areaThe playbook wants this number rising, never zero. If an auditor asks why near-misses rose this year, the playbook’s answer is that workers now report more.
PPE compliance % on shop-floor auditsThe playbook sets 95% or more, measured by observation on the floor, not by counting what was issued.
Fire-drill evacuation time to the assembly pointThe playbook sets four minutes or less, with a drill in each zone every quarter. A drill once a year, it says, is only for show.
ETP discharge conformanceThe playbook’s target is 100%: pH 6–9, with BOD, COD, TSS and colour inside your local limits. Discharge above the limit starts the playbook’s stop, divert, treat and re-test sequence.
ZDHC chemical conformance %The playbook’s target is 100%, and it treats conformance as a procurement result: a chemical that fails the MRSL screen should not pass the gate.

What the agent works from

Records it reads

  • Risk assessment
  • PPE register
  • Fire-drill log
  • Incident report and near-miss log
  • CAPA tracker
  • ETP lab log and discharge report
  • Safety data sheet (SDS)
  • ZDHC InCheck report

In your ERP

The factory’s ERP connection gives the HSE agent no records, whatever your ERP holds, and it writes nothing to the ERP. Registers, ETP logs and SDS files come from files you upload and Google Sheets you connect. It reads a supplier’s reply in Gmail or Outlook; an SDS attached to it comes in through Gmail or as an uploaded file.

One ERP connection serves the whole factory: SAP Business One, SAP S/4HANA, Odoo, Oracle NetSuite, Microsoft Dynamics 365, WFX Cloud ERP or Datatex NOW. This agent reads only the records named above; we check yours on the call.

In your tools

When you ask, searches Gmail for a supplier’s emails, reads recent Outlook emails or reads the CAPA tracker in Google Sheets. Prepares an email asking a supplier for a current SDS or a lab for a re-test, CAPA tracker rows, and WhatsApp or Slack messages to fire wardens and CAPA owners. An admin approves or declines each one; it runs only if approved.

Tools named today: Gmail, Outlook, Google Sheets, Slack and WhatsApp Business.

Never made up

  • Incident details, injury classifications or investigation findings
  • Discharge readings, permit limits or monitoring results
  • Chemical inventories, SDS content or ZDHC conformance status
  • Training completion or drill attendance records

If it is not in your connected data, the agent says so.

Belongs to another department

What the HSE playbook covers

  • SOP: from incident to closed CAPA

    Classify every incident: near-miss, first-aid, lost-time or reportable. Investigate within 24 hours, find the root cause with 5 Whys, and set a CAPA with an owner and a due date. Log every near-miss, because the playbook treats under-reporting as the biggest hidden risk. A lost-time incident goes to the HSE head, plant head and CEO within one hour.

  • Decision rule: discharge above the regulator’s limit

    Stop discharge, divert to the balance tank, dose or treat, re-test, and resume only once readings are within limits. Inform the regulator under your local SOP if the deviation is significant. The playbook also notes that raw dye-house influent at pH 10–12 is normal; equalisation brings it to pH 6.5–8.5 before the biological stage.

  • KPI: ZDHC chemical conformance at 100%

    The playbook treats conformance as a procurement job: chemicals are screened against the ZDHC MRSL before they enter the gate. Each month the chemical inventory goes onto the ZDHC Gateway, which returns the InCheck report. A restricted chemical found in stock goes to Sourcing and HSE for quarantine and safe disposal.

  • Heuristic: an ETP log that always passes

    When the in-house lab log always passes but the regulator keeps visiting, the playbook reads it as calibration drift in the lab test, and says to cross-check the daily values against third-party results regularly. For a brief spike that settles, it says to check the upstream batch, often a dyeing recipe, and the operator’s technique.

Written as general textile practice and reviewed by four independent AI models. Not yet signed off by a human subject-matter expert. Upload your own SOPs and standards, and every answer shows which source it used.

Ten questions it ships with

The template’s starter questions. Your team can edit them, or ask in its own words.

  • Risk assessment for an area

    What does the risk assessment record for this area, which controls apply, and when was it last reviewed?

  • Incidents this period

    Which incidents were reported this period, what did the investigations conclude, and which corrective actions are still open?

  • PPE compliance for a section

    What does the PPE register show for this section — issued, due for replacement, and any gaps recorded?

  • ETP discharge against permit

    What does the ETP log show for this period against the permitted discharge limits, and were there any exceedances?

  • ZDHC status for a chemical

    What is the ZDHC conformance status of this chemical, what does its MSDS record, and is it on our approved list?

  • HSE status summary

    Prepare an HSE status summary for the month from the registers and reports: incidents, drills, PPE, and environmental monitoring.

  • Fire drills completed

    Which fire drills have been completed this year, in which areas, and what did each record?

  • Near-misses by area

    Show near-misses reported this quarter by area, and tell me where they cluster.

  • Chemicals awaiting approval

    Which chemicals in use are not yet on the approved list, and what documentation is missing for each?

  • Overdue corrective actions

    Which HSE corrective actions are overdue, what do they cover, and how far past their due date are they?

HSE: questions before a demo

Our incident book and fire-drill log are on paper. Can it still help?

Only with what is connected. A scanned page or a photo of a register has no text to read. Once incidents, near-misses and drills are typed into a Google Sheet, or an Excel or CSV file uploaded to HSE, the agent answers from them. From an uploaded file it counts and averages from the rows, using a CSV or an Excel file’s first sheet, filtered by exact values such as a month or an area, so keep a month column. Risk assessments, SOPs and SDS files that exist as Word files or text PDFs can be uploaded as they are.

Can it read our ETP flow meters or the online effluent monitoring (OCEMS) feed?

No. Mavick does not connect to the ETP, its meters and probes, or an OCEMS feed. It reads the ETP lab log as your chemist records it, in a Google Sheet or an uploaded Excel or CSV file, and the third-party test and ClearStream reports you upload as text PDFs. If your OCEMS exports its readings to a file, upload that file and the agent reads them there. It answers when someone asks; it does not check the log between questions.

Can it check our chemicals against the ZDHC MRSL?

Not as a screen. It reads what you upload: the MRSL, your approved chemical list, SDS files and the InCheck report exported from the ZDHC Gateway. It does not connect to the Gateway itself. If your chemical inventory sheet has an approved column, it counts the chemicals marked not approved and cites the rows it finds. It never makes up a conformance status: that comes from the InCheck report or the supplier’s evidence, and if a chemical is in none of your files, it says so.

Can the agent quarantine a restricted chemical in our ERP?

No. The HSE agent writes nothing to the ERP: it cannot block a goods receipt, move stock, change quantities or add a note. If you ask, it drafts an email or a WhatsApp Business message asking your stores team to hold the lot, naming the chemical and lot from your inventory file. An admin approves or declines it, and it is sent only if approved. Quarantine and safe disposal stay with Sourcing and HSE, as the playbook says.

Will it report an ETP breach to the regulator by itself?

No. If you ask, it drafts the report your SOP calls for, as an email or a document, with the log readings and the containment steps on record. An email waits for an admin, usually the HSE head as department admin, who approves or declines it, and it is sent only if approved. Whether a deviation is significant enough to report stays the HSE head’s decision. Mavick has no autonomous mode, and nobody can switch the approval step off.

Can it work out our LTIR?

Yes, when both inputs are uploaded to HSE. With the incident register and a sheet of hours worked for the period as Excel or CSV, the agent counts the lost-time incidents from the register and sums the hours from the hours sheet, showing each figure with the rows behind it. It then works out the rate on the base your factory uses, such as 200,000 hours. Hours belong to Human Resources, and the HSE agent cannot read HR’s records, so HSE needs its own copy. If the hours are not in HSE’s data, it says so instead of estimating them.