The four problems that fill a dyeing master’s week
Each one shows up in a record you already keep: the daily RFT sheet, the batch card, a buyer’s test report, the ETP log. The cost lands in machine hours, chemicals and water, or in a claim or an audit finding.
Batches that miss right first time
A batch misses shade, fastness or hand-feel on the first dyeing and goes back for a shading addition, a strip and re-dye, or an extra wash. The jet runs it twice, the next shift inherits it, and delivery slips. Each re-dye spends the chemicals, steam and water again, and weakens the fabric.
15%
Share of baths that no longer needed re-processing at one Bangladeshi yarn-dyeing factory, once process and machine fixes lifted its bulk-to-bulk RFT from 80% to 95.5%.
Source: World Bank Group (IFC PaCT), Cleaner Production Case Study: Right First Time (RFT) Improvement Through Process Optimization, Evince Textiles Limited (opens in a new tab), 2021.
Shade that drifts between the lab, bulk and the next jet
The lab dip passes and bulk comes off shade. The same recipe on two jets gives two shades. A recipe that ran well for months creeps up in ΔE when the dyestuff lot changes. Each fix means topping, extra time at temperature or a strip, in the sample room and in bulk, and the fabric can lose GSM. Meanwhile the dyeing master and the lab in-charge work out which step changed.
22 hours
An 8-hour sample dyeing can stretch to 22 hours when shade matching needs topping or extra heat, said the DGM (Dyeing) of a Bangladeshi knit group at a 2024 industry meeting.
Source: Textile Today, Strategies to minimize fabric process loss and reduce rejection rates by optimizing dyeing processes discussed at TTIH Textile Processing Innovation Cell Meeting (opens in a new tab), 2024.
An ETP log that has to stand up to an audit
Buyers’ auditors and your HSE team ask for the ETP record: pH, BOD, COD, TSS, colour and discharge volume, shift by shift, against the limits. When the log has gaps or sits in a paper register, nobody can produce a clean summary in time. A 2017 Transparency International Bangladesh study names poor record keeping as one reason many ETPs fall short. The ETP operator and the processing manager carry that risk.
29%
Share of Bangladeshi wet-processing units with an ETP that were found compliant, in a 2014 study cited in a 2023 paper. Only 61% had an ETP at all.
Source: PLOS Sustainability and Transformation, Water and chemical consumption in the textile processing industry of Bangladesh (opens in a new tab), 2023.
A fastness claim on a lot that has already shipped
The shade passed, but the buyer’s lab reports a fastness fail, such as wet rubbing on a deep black or red. The QA head must answer, and the dye house must produce the retain sample, its own retest and the batch card with its fixing and wash-off steps. The playbook gives 72 hours to reconcile the retest with the buyer’s report and the standard it used. Until then, the claim stays open on a shipped lot.
What the dyeing agent does when you ask
It works from your recipe sheets, batch cards and test reports, and your Odoo production orders and transfers. Each answer shows the records it drew on, and anything it sends or writes waits for an admin to approve or decline.
The approved recipe, and where a batch left it
Answers with sources
Ask for a shade, batch or quality, and the agent answers from your recipe sheets and lab dip cards: the locked recipe, the lab dip behind it, the dosing and the dyestuff lots. Ask why jet 3 and jet 5 gave two shades on one recipe, and it sets each batch card beside the locked recipe. It lists the recorded values that differ, and the values that were never recorded, citing each card.
Ask“Jet 3 and jet 5 ran recipe R-0912 this week and gave two shades. Compare their batch cards with the locked recipe.”
RFT and re-dye %, worked out from your batch rows
Answers with sources
Upload the daily RFT sheet as an Excel or CSV file. The agent counts RFT and re-dye batches from the actual rows, for the month, shade depth, fibre, machine or buyer you name (up to two at once), and cites the rows it used, so anyone can check the number.
Ask“What was our RFT on dark shades on jet 3 in this month’s sheet? Cite the batch rows you counted.”
Test reports read against the buyer’s standard
Reads your documents
Upload your in-house and third-party test reports and the buyer’s standard. The agent sets each result against the required grade or limit: wash, dry and wet rubbing, perspiration, light, shrinkage. It names the method each report used, such as ISO 105-C06 for washing or ISO 105-X12 for rubbing, and cites both documents.
Ask“Does lot 118 meet the buyer’s fastness standard? Show each test, the method and the grade required.”
Water, steam and chemical per kilo, by shade and machine
Creates files
Upload the month’s water, steam and chemical consumption and the kilos dyed as an Excel or CSV file. The agent totals them from the rows for the shade depth, machine or month you name, works out use per kilo, and builds the comparison as a spreadsheet that cites the rows. The playbook reads a rising figure as ETP load, recipe drift or machine inefficiency. It is not connected to your meters.
Ask“How much water per kilo did jet 3 use on dark shades last month? Put it in a sheet beside the month before.”
A recipe hold, sent to the people who must stop using it
Acts in your tools
After two re-dyes on one buyer order, the playbook says to freeze the recipe and re-spec it. The agent lists the batches that ran it and drafts the hold notice: a WhatsApp Business or Slack message to the dyeing master and the shift in-charges, and a row for your recipe-hold sheet in Google Sheets. A department admin approves or declines each one, and nothing is sent or written unless approved.
Ask“Second re-dye on order 4471. List the batches that used its recipe and draft the hold notice for the shift in-charges.”
Three moments from a week in the dye house
A bulk batch comes off shade
Dyeing master
A bulk batch comes off the jet above the playbook’s ΔE 1.0 against the approved standard.
Asks
“D-2417 is off shade, too red at D65. What on its batch card differs from the approved recipe?”
The agent
Reads the batch card, the locked recipe sheet and the pre-treatment record side by side. It lists each recorded value that differs: liquor ratio, salt and soda, temperature holds, pH, time. It says which values were not recorded and whether the dyestuff lots match the lab dip’s. It quotes the playbook: a hue shift points to dye ratio, so correct only with the recipe’s own dyes, or strip and re-dye.
Result
The dyeing master chooses between a shading addition and a strip from the recorded deviations, with every record cited.
Handing the jets to the night shift
Shift in-charge
Half an hour before shift change, with batches still in dyeing and wash-off.
Asks
“Prepare the shift handover from today’s batch cards and send it to the night shift in-charge on WhatsApp.”
The agent
Reads the day’s batch cards and the machine log you uploaded, and writes the handover as a document: batches completed, deviations recorded, batches in progress with their stage, corrections still open. It then drafts a WhatsApp Business message to the night shift in-charge with the handover in it.
Approval
The handover message waits for the department admin, who approves or declines it. It is sent only if approved, and the audit trail records who decided.
Result
A written handover of the day’s batches and open deviations, kept as a document, and a message sent to the night shift only if approved.
A buyer’s lab reports a wet-rub fail
Processing manager
The buyer’s test report on a shipped black lot is uploaded to the dyeing department: shade passed, wet rubbing failed.
Asks
“Put our test report for lot 118 beside the buyer’s report and the batch card, and make the reconciliation sheet.”
The agent
Reads both reports and the buyer’s standard, and lists each test with its method, the grade required and the grade achieved. It adds the batch card’s fixing and wash-off steps, and the playbook’s guidance for blacks that pass shade and fail wet rub: fixing chemistry and an extra wash, never more dye. It builds the reconciliation as a spreadsheet, citing each document.
Result
A side-by-side sheet to start the 72-hour reconciliation the playbook sets, citing both reports and the batch card.
What re-dyes and lost hours cost, in published figures
Most of these figures come from published work on Bangladeshi dye houses, each cited at the source. None is a Mavick result. A pilot measures your own: baseline the dyeing KPIs below, then read them again.
The chemical bill for batches dyed twice
US$254,000 a year
What re-processing 3 t of its 30 t daily output cost one Bangladeshi knit mill in chemicals: about 500 t a year. The mill’s own 2012 estimate, made when it automated its dyeing lab.
How the agent helps
The agent does not dye or dispense. When you ask, it works out RFT and re-dye % from your batch rows. It sets each re-dye’s batch card beside its recipe. It builds the sheet for your weekly review of non-RFT batches by recorded root cause, so the repeat causes sit on one page.
Track: Re-dye % and bulk RFT %, by shade depth and machine
Source: Natural Resources Defense Council (Clean by Design), Standout Practices at High-Performing Bangladeshi Textile Mills (opens in a new tab), 2012.
Water and chemical per kilo, worked out from your rows
136 L/kg
Average dye-house water per kg processed across 18 Bangladeshi wet-processing factories, with a wide spread between them. Chemicals averaged 449 g per kg, from 152 g to 705 g.
How the agent helps
Every re-dye adds water, energy and chemicals on top. Upload the month’s consumption and production as an Excel or CSV file, and the agent totals them from the rows and works out use per kg for the shade depth or machine you name. The playbook reads a rising figure as ETP load, recipe drift or machine inefficiency.
Track: Steam, water and chemical cost per kg, by month
Source: PLOS Sustainability and Transformation, Water and chemical consumption in the textile processing industry of Bangladesh (opens in a new tab), 2023.
Answers that do not wait for the dyeing master
Nearly 20%
Share of the working week that managers and professionals spend looking for internal information or for colleagues who can help. A 2012 cross-industry estimate, not a textile one.
How the agent helps
SOPs, past batch cards, correction notes and the playbook are answerable on every shift, with the source beside each answer. When the master is on leave, the night shift can still ask which recipe was approved and why the last correction was made, and get the record or a plain “not in your connected data”.
Track: Time to find the approved recipe, lab dip and dosing for a batch
Source: McKinsey Global Institute, The social economy: Unlocking value and productivity through social technologies (opens in a new tab), 2012.
What to baseline before a pilot
Measure each one before the pilot starts, then again at its end.
| KPI to baseline | Why it matters |
|---|---|
| Bulk RFT %, by fibre and shade depth | The playbook’s headline number: a target of 80% or more for cotton reactives, within a usual 75–85% band. It notes that recipe drift shows as RFT slipping 3–5 points over two weeks. |
| Re-dye % | The playbook sets 5% or less. Each re-dye spends chemicals, energy and machine time again, and weakens the fabric. |
| ΔE of the first batch against the standard | The playbook sets 1.0 or less in ΔEcmc(2:1) at D65, unless the buyer names another equation. A rising trend points to dyestuff lot variance or scour drift. |
| Lab-dip cycles to shade approval | The playbook aims for two or fewer on standard accounts. Once cycles pass three with no approval, it says to stop and ask the buyer’s QC for a swatch they accept. |
| Fastness pass rate on shipped lots | The playbook’s target is 100%. Any fail on a shipped lot risks a buyer claim, and once a claim arrives the playbook gives 72 hours to reconcile your results with the buyer’s. |
| ETP discharge conformance | The playbook’s target is 100%. Any out-of-spec discharge is a regulatory event. If it lasts over two hours, the playbook says to escalate to the ETP operator, the processing manager and HSE, and to halt discharge. |
What the agent works from
Records it reads
- Lab dip card
- Recipe sheet
- Batch card
- Shade approval
- Spectro report
- Fastness test report
- Daily RFT sheet
- ETP log
In your ERP
Reads Odoo production orders (product, quantity, status) and stock transfers. Dye and chemical receipts show only as transfers, never as quantities on hand; dye stock and batch results come from files or a Google Sheet. In Odoo it drafts a production order’s planned start or assignee, or a transfer’s note or source document; an admin approves or declines.
One ERP connection serves the whole factory: SAP Business One, SAP S/4HANA, Odoo, Oracle NetSuite, Microsoft Dynamics 365, WFX Cloud ERP or Datatex NOW. This agent reads only the records named above; we check yours on the call.
In your tools
Drafts the shift handover as a WhatsApp Business or Slack message, prepares the day’s batch results as new rows for your RFT sheet in Google Sheets, or proposes an email through Gmail or Outlook asking your dyestuff supplier to reserve a single lot for a buyer’s run. An admin approves or declines each one, and nothing is sent or written unless approved.
Tools named today: Gmail, Outlook, Google Sheets, Slack and WhatsApp Business.
Never made up
- Dye and chemical recipes, concentrations or dosing quantities
- Process parameters: pH, temperature, time, pressure, flow, liquor ratio, dwell
- Lab dip references, shade approvals or buyer sign-offs
- Fastness, shrinkage or ETP discharge readings
- Batch numbers, machine assignments or RFT figures
If it is not in your connected data, the agent says so.
Belongs to another department
- Greige construction, EPI/PPI and weaving defectsWeaving
- Knitted structure, GSM setting and knitting defectsKnitting
- Printing pastes, screens and registrationPrinting
- Final finishing recipes, sanforizing and shrinkage controlFinishing
- Buyer shade standards and approval correspondenceMerchandising
- Effluent permits and environmental reportingHealth, Safety & Environment
What the Dyeing & Processing playbook covers
SOP: lab dip to bulk
Two or three lab-dip variants, one approved by the buyer. The recipe is scaled to bulk and the recipe sheet locked. The first batch runs at half-bulk and is spectro-checked: ΔE 1.0 or less goes ahead, above that adjust and re-dye. ΔE means ΔEcmc(2:1) at D65 unless the buyer’s spec names another equation.
Decision rule: a bulk batch off shade
Check three causes in order: the recipe was scaled wrongly, the scour or bleach was uneven, the dyestuff lot shifted strength. Correct only with the recipe’s own dyes, typically no more than 10% of the original depth. If that cannot close the gap, strip and re-dye: outside dyes create a metameric match.
KPI: batch-to-batch shade on one order
The shade-tolerance reference sets ΔE 0.8 or less between any two batches on the same order, even when each passes against the standard. Two batches at opposite edges of the tolerance can sit 2.0 apart, and they end up in the same garment.
Heuristic: metamerism is where claims happen
Measure every shade at D65 daylight, TL84 store light and incandescent A. The playbook reads the metamerism index as the gap between ΔE at D65 and at TL84. Under 0.5 the match is stable. Over 1.0 the batch will look wrong in the store though it passed at D65, so the playbook says to treat it as a fail and re-spec the recipe, not pass it as borderline.
Written as general textile practice and reviewed by four independent AI models. Not yet signed off by a human subject-matter expert. Upload your own SOPs and standards, and every answer shows which source it used.
Ten questions it ships with
The template’s starter questions. Your team can edit them, or ask in its own words.
Approved recipe for this batch
Show me the approved dyeing recipe for this batch, including the lab dip it was scaled from, and the full chemical dosing.
Machine parameters versus approved settings
Compare the current machine parameters with the approved process settings for this batch — temperature, time, pH, liquor ratio and dosing — and flag every deviation.
Why a batch missed shade
This batch missed shade. Compare its batch card against the approved recipe and tell me which step or parameter deviated.
Right-First-Time this month
What was our Right-First-Time percentage this month, and which shades and machines account for most of the rework?
Full batch card for a lot
Walk me through the batch card for this lot: pre-treatment, dyeing, washing, fixation, drying and finishing, with the recorded parameters at each stage.
Fastness results against the standard
What are the fastness and shrinkage results for this lot, and do they meet the buyer’s required standard? Cite the test report and the standard.
pH and temperature deviations
Show the pH and temperature trace for this batch against the recipe setpoints, and identify where and for how long it ran outside tolerance.
Effluent load from the dye house
What effluent load and pH did the dye house send to the ETP over this period, and which processes or shades contributed most to it?
Batches pending re-processing
Which batches are pending rework or re-processing, what was the reason recorded for each, and how long have they been waiting?
Shift handover with deviations
Prepare a shift handover from the batch cards and machine logs: batches completed, deviations recorded, batches in progress, and what the next shift must watch.
Dyeing & Processing: questions before a demo
Can the agent change a recipe in our ERP?
No. The only Odoo changes the dyeing agent can draft are a production order’s planned start or assignee, and a note or source document on a stock transfer, and each one waits for an admin to approve or decline it. For a recipe hold, the agent drafts the notice instead: the message to your dyeing master and shift in-charges, or the row in your recipe-hold sheet. Nothing is sent or written unless an admin approves it, and nobody edits a waiting action.
Our batch cards are on paper. Can it still help?
Only with what is connected. The agent cannot read a card that stays on the shop floor, or a scan or photo of one. Once batch results are typed into a Google Sheet, or an Excel, CSV or PDF file you upload, it answers from them, and from an uploaded Excel or CSV file it works out RFT from the rows. If your SOPs, recipe sheets and test reports already exist as files, upload them as they are and start there while the batch records move into a sheet.
Can it read pH and temperature straight from our jets?
No. Mavick does not connect to dyeing machines or their controllers, and your ERP connection gives the dye house no machine readings. If a jet’s trace is exported to a file you upload, or the readings are typed into a Google Sheet, the agent reads them beside the recipe setpoints and points to where the trace shows them outside tolerance, citing the rows. If a reading is not there, it says so.
Will the dyeing agent see our costing sheets or merchandising’s buyer emails?
No. The dyeing agent sees only what is connected to the dyeing department, and that boundary is built into how Mavick stores and retrieves everything. Costing sheets and merchandising’s mail stay in their own departments, and the dyeing agent cannot fetch from them. Asked about buyer shade standards or approval correspondence, it says Merchandising owns them. If you connect a mailbox to the dyeing department itself, its agent reads that mailbox when asked.
Can it read our spectrophotometer QC reports?
Yes, when you export them. Upload the QC report from your spectrophotometer software as a PDF, Excel or CSV file, and the agent reads the ΔE, the equation, the illuminants and the pass or fail for each batch. It compares batches with the approved standard and cites the report. It does not connect to the instrument, and it does not formulate recipes or match colour: that stays with your colourist and colour-matching software.
Which ΔE equation does it go by when the buyer’s lab disagrees with ours?
It does not measure colour. It reads the ΔE and the equation each report records, and the one the buyer’s colour specification names. The playbook defaults to ΔEcmc(2:1) at D65 and says to confirm which equation the buyer’s lab used before you dispute a shade claim, because ΔE*ab, ΔEcmc and ΔE00 give different numbers for the same pair. Once the buyer’s colour specification is uploaded to Dyeing, or shared across the factory, the agent quotes it.
Bring Dyeing & Processing. We’ll build it on the call.
Book a 30-minute demo (opens in a new tab)- support@mavick.si
- Demo calendar
- calendly.com/safock/30min (opens in a new tab)