Where a print run loses colour, metres and paste
Each one shows up in a record the print floor already keeps: the strike-off card, the screen register, the print log or the colour kitchen’s mixing sheet. The cost is re-runs, re-engraves, rejected panels and paste washed to the drain.
Paste mixed by experience, with extra made to be safe
The colour kitchen sizes each paste batch by experience and mixes extra so the machine never runs short. The leftover at each colour change often goes to the ETP. Viscosity and pH drift between mixes, and thin paste gives halo and smear. A senior production officer in printing at a Bangladeshi knit composite told Textile Today in 2022 that meeting the required pH and viscosity of all-over-print paste is a struggle.
5 to 10 pastes
Printing pastes usually needed for a single pattern, up to 20 in some cases. The EU reference document also names incorrect measurement and mixing extra paste to prevent a shortfall as two main causes of paste residues.
Source: European Commission Joint Research Centre (European IPPC Bureau), Best Available Techniques (BAT) Reference Document for the Textiles Industry (opens in a new tab), 2023.
The strike-off was approved, and bulk printed off-shade
The buyer signs the strike-off, then bulk comes off-shade, or batch 2 does not match batch 1. The playbook says claims start in composite shades, where two pastes overlap. Often the bulk fabric was prepared differently: Cotton Incorporated reports that as many as 60% of printing defects trace back to fabric preparation. The print master re-mixes and re-runs, QA holds the lot, and a misprint cannot be repaired.
Last month’s screen set, or an earlier file on the RIP
Bulk must run on the version the buyer approved. The engraving room, the CAD desk and the print floor each keep their own list, so a design can reach the floor on an old screen set or an earlier file. A buyer changes one Pantone and nobody strikes it off again. The print master finds out from the shade on the table, and the whole run, with the buyer’s claim, is the cost.
Screens that wear out while nobody counts impressions
A rotary screen dents in handling, wears thin over many impressions, or chokes when paste dries in the mesh. If the register counts weeks, not impressions, a design gets booked on a worn set. Screen marks and choking become rejected metres, and the order waits for a re-engrave. Printing staff at two Bangladeshi groups named screen jams and mesh problems as frequent all-over-printing faults (Textile Today, 2022).
From strike-off card to print log: what the printing agent does
It reads the strike-off cards, recipes, registers and logs you connect or upload, and names the file behind each answer and the rows behind each figure it adds up. A change it prepares waits for an admin to approve or decline, and runs only if approved.
The approved strike-off, and what changed in bulk
Answers with sources
Name a design and colourway, and the agent answers from your strike-off cards and colour recipes: the recipe by %, the fabric reference and the buyer’s approval. Ask why two batches differ, and it sets their recorded recipes, paste lots and curing side by side. It walks through the playbook’s three checks, names any value never recorded, and says the fabric-prep check needs Dyeing & Processing’s records.
Ask“Batch 2 of design F-2231, colourway 3, printed duller than batch 1. Compare the paste recipes and curing recorded for both.”
The locked screens or file, and screens near their limit
Reads your documents
Upload the digital file registry and strike-off cards, and keep the screen register as a file or Google Sheet. Ask what a design should print on, and the agent quotes the locked screens or file version, the date and who signed it off. Ask which screens are near their impression limit on record, and it lists those it finds, with the designs booked on them, citing each row. It reads the registry, not the design files.
Ask“Which screens and file version are locked for F-2231, colourway 3, and which of its screens are near their impression limit?”
Paste against the norm, added up from the mixing sheet
Answers with sources
Upload the colour kitchen’s mixing sheet as an Excel or CSV file with design and week columns. The agent adds up the kilos mixed for a design from the rows and sets the total beside the norm on file. It also counts the mixes whose viscosity check reads Fail on one shift or for one colour. It lists the rows it used. It does not tell the kitchen how much to mix: that stays with the colour kitchen in-charge.
Ask“How many kilos of paste did we mix for design F-2231 in week 46, against the norm on file?”
Rejected metres by cause, built into the run summary
Creates files
From the print log, uploaded as Excel or CSV with a week column, the agent adds up metres printed, and metres rejected for each recorded cause you ask about: registration, colour, smear, curing. It puts the totals into the week’s rejection summary spreadsheet, largest cause first, with the defect rate beside the playbook’s 2% target. Ask it to add one machine’s figures and it edits that part, keeping each revision.
Ask“How many metres did we reject for registration in week 46? Add the total to the week’s rejection summary from the print log.”
The locked version, drafted for the shift before the run
Acts in your tools
Ask before a run, and the agent builds the playbook’s pre-run checklist from your records: approved strike-off on file, screens or file at the locked version, paste viscosity-checked. It marks what it cannot find on record. It drafts a WhatsApp Business or Slack message to the shift supervisor naming the screen set or file version. A department admin approves or declines it, and it goes out only if approved.
Ask“Design F-2231 runs on machine 4 tonight. Make the pre-run checklist and draft a WhatsApp to the shift supervisor with the locked screens.”
The first 10 metres, the screen room and a run held for approval
Bulk is off-shade against the approved strike-off
Print master
The first 10 metres of a pigment run are pulled and checked, as the playbook asks, and the shade sits away from the strike-off.
Asks
“Bulk on design F-2231 is off the strike-off at D65. What differs from the strike-off card in recipe, paste lot or curing?”
The agent
Reads the strike-off card, the colour recipe, the paste mixing sheet and the print log side by side. Lists the recorded values it finds that differ: recipe %, paste batch and its viscosity, curing temperature, speed and dwell. Says which of the playbook’s three checks it cannot make from printing’s records, such as the fabric preparation, which belongs to Dyeing & Processing. Cites each record.
Result
The print master sees which recorded values moved, and which check needs the fabric preparation record from Dyeing, before deciding whether the run goes on.
Screens near the end of their recorded life
Screen room in-charge
Next week’s print plan is out, and two repeat designs are booked on old screen sets.
Asks
“Which screens are near or past their recorded life, and which designs use them? Draft a re-engrave request to the engraving room.”
The agent
Reads the screen register in Google Sheets: screen number, design, impressions recorded and the life limit on record. Lists the screens it finds at or near that limit and the designs that use them, citing each row. Prepares a re-engrave email to the engraving in-charge, to send through Gmail, with the screen numbers and designs exactly as recorded.
Approval
The email waits for the printing head, as department admin, to approve or decline. If approved, Gmail sends it to the engraving in-charge; if declined, nothing is sent. The audit trail keeps who decided.
Result
A list of screens near their recorded limit, matched to the designs that use them, and a re-engrave request that leaves Mavick only if the printing head approves it.
A confirmed run held for a strike-off
Print planner
A confirmed-PO run is due to start tomorrow, and its strike-off is still waiting on the buyer.
Asks
“Which strike-offs are still pending, when were they sent, and which orders wait on them? Draft a new planned start for F-2240’s order: Planning agreed the 18th.”
The agent
Reads the strike-off register for each pending strike-off: design, round, date sent and the order it belongs to. Reads the production orders in Odoo, shown with the time they were fetched. Drafts the change to the order’s planned start, using the date the planner gave it. It never picks a date itself.
Approval
The change waits for the printing head, as department admin, who approves or declines it. The planned start moves in Odoo only if approved.
Result
Bulk waits for the buyer’s approval, as the playbook requires, and the order’s start changes in Odoo only if the printing head approves it.
What off-shade runs, misprints and spare paste cost
The figures come from published sources (a Cotton Incorporated bulletin, a Turkish mill’s paste study and a Bangladeshi industry meeting), each cited at its source. They are not Mavick results. In a pilot you record your own printing KPIs first.
Off-shade bulk checked against the strike-off card
As many as 60%
Share of textile printing defects that can be traced to fabric preparation problems, a figure Cotton Incorporated reports second-hand in its 2003 bulletin on cotton printing. It covers all printing defects, not off-shade alone.
How the agent helps
When you ask, it sets the strike-off card beside the bulk run’s records: fabric reference, recipe, paste or ink lot, curing or fixation, and lists what differs. It holds no fabric-prep records: it says that check needs Dyeing & Processing. From an uploaded spectro sheet with a design column, it works out a design’s average or highest ΔE.
Track: Bulk vs strike-off ΔE at D65, by design and machine
Source: Cotton Incorporated, Textile Printing (opens in a new tab), 2003.
Fewer metres and panels lost to misprints
1 inch, 1 panel
In knit all-over printing, one inch of misprint can cost a whole garment panel, said a mill’s director of printing production at a 2024 Bangladeshi industry meeting. A practitioner’s remark, not a measured rate.
How the agent helps
From the print log you upload, the agent adds up rejected metres for each recorded cause you name, works out the defect rate from the rows and lists the largest cause first. It sets the rate beside the playbook’s 2% target and its 5% line for a process review.
Track: Defect rate by cause: registration, wash-out, smear
Source: Textile Today, Strategies to minimize fabric process loss and reduce rejection rates by optimizing dyeing processes discussed at TTIH “Textile Processing Innovation Cell Meeting” (opens in a new tab), 2024.
Paste mixed for the run, not for safety
23%
Share of prepared print paste that ended up as waste in one Turkish mill’s rotary pigment printing on runs over 2,000 m of sheeting, where operators sized each batch by experience. Taken from about 600 production records.
How the agent helps
The agent does not work out how much paste to mix. From the mixing sheet you upload, it adds up the kilos mixed for a design or a colour, and the leftover where you record it. It sets the totals beside the norm on file, so the colour kitchen in-charge sees which designs take extra paste run after run.
Track: Paste consumption against norm, by design
Source: Sciendo (CORTEP 2022 proceedings), Rotary Printing: Paste Reduction and Paste Calculation Using Statistical Analysis (opens in a new tab), 2023.
What to baseline before a pilot
Measure each one before the pilot starts, then again at its end.
| KPI to baseline | Why it matters |
|---|---|
| First-pass strike-off acceptance | The playbook’s target is 80% or more. When a strike-off fails three or more buyer reviews, it says to bring Design, Merchandising and the print master together to review the artwork separations. |
| Bulk vs strike-off ΔE at D65 | The playbook sets 1.5 or less. It shows whether bulk still matches what the buyer signed, and the playbook’s per-run report pairs the print log with spectro readings from the first, middle and last roll. |
| Defect rate by cause: registration, wash-out, smear | Rejected metres carry the fabric, paste and machine time already spent on them. Counted by cause, they show which fix comes first. |
| Screen life: impressions per screen | The playbook says to track it per pattern and to re-engrave as a screen nears the end of its life. Its rule of thumb: count impressions, not weeks. |
| Wash-fastness pass rate on shipped lots | The playbook aims for 100%. For a fail on a shipped lot, its escalation rule says to bring in the QA head, the print master and the compliance head within 24 hours. |
| Paste consumption against norm, by design | The playbook lists recipe consumption among its weekly figures. Set beside each design’s norm, it shows which designs the kitchen over-mixes. |
What the agent works from
Records it reads
- Strike-off card
- Colour recipe
- Print log
- Digital file registry
- Screen register
- Strike-off register
- Colour kitchen mixing sheet
- Rub and wash fastness report
In your ERP
Reads Odoo production orders (order, product, quantity, status) and Odoo stock transfers, with fetch times. Drafts an order’s planned start or assignee, or a transfer note, which an admin approves or declines; it runs only if approved. Pigment and binder stock comes from an uploaded stock report; strike-offs, screens and print logs from files and sheets.
One ERP connection serves the whole factory: SAP Business One, SAP S/4HANA, Odoo, Oracle NetSuite, Microsoft Dynamics 365, WFX Cloud ERP or Datatex NOW. This agent reads only the records named above; we check yours on the call.
In your tools
Reads the screen register or strike-off register in Google Sheets when you ask. Prepares the pre-run message for WhatsApp Business or Slack, a re-engrave request to send through Gmail or Outlook, or new rows for a print log kept in Google Sheets. Each waits for an admin’s approve or decline, and runs only if approved.
Tools named today: Gmail, Outlook, Google Sheets, Slack and WhatsApp Business.
Never made up
- Colour-paste recipes and pigment or dye concentrations
- Screen numbers, repeat sizes or digital file versions
- Curing and fixation temperatures, speeds or dwell times
- Strike-off approvals and buyer colour sign-offs
If it is not in your connected data, the agent says so.
Belongs to another department
- Base fabric dyeing and pre-treatmentDyeing & Processing
- Post-print finishing and hand-feel finishesFinishing
- Artwork and repeat developmentDesign & CAD
- Buyer colour standards and approvalsMerchandising
What the Printing playbook covers
SOP: strike-off to bulk
Engrave the screens or prepare the digital file with the buyer’s separations. Strike off on a sample of the bulk fabric, check the colours on the spectro and get the buyer’s approval. Then lock the screen or file version and tag the strike-off in the registry. Bulk runs only on the approved version.
Decision rule: the strike-off matched, bulk did not
Make three checks. Was the bulk fabric prepared differently from the strike-off fabric? Did the paste batch use a different recipe or dyestuff lot? Did the machine’s dwell time or steam pressure change? The playbook says most cases are a fabric-prep mismatch, so always strike off on fabric from the bulk preparation.
KPI: defect rate, and registration first
The playbook’s target for registration, wash-out and smear defects is 2% or less; above 5% calls for a process review. On rotary machines it names registration drift between cylinders as the leading defect: fit marks checked against the repeat every shift, and the first 10 metres of every batch pulled and checked.
Heuristic: pigment cracks, so check the cure first
When a pigment print cracks after washing, the playbook says it is under-cured 80% of the time, and the other 20% is the binder ratio. So check the oven dwell first, then rebalance binder and pigment. Its typical pigment cure is about 150°C for 3 minutes; under-time washes out, over-time hardens the hand-feel and shifts the shade.
Written as general textile practice and reviewed by four independent AI models. Not yet signed off by a human subject-matter expert. Upload your own SOPs and standards, and every answer shows which source it used.
Ten questions it ships with
The template’s starter questions. Your team can edit them, or ask in its own words.
Approved colour recipe for a design
What is the approved colour recipe and strike-off for this design and colourway? Show the paste composition.
Current screen or file version
Which screens or digital files are the current approved version for this design, and when were they last updated?
Why colour moved between batches
Colour has moved between these two print batches. Compare the paste recipes and curing parameters recorded for each and tell me what differs.
Registration and curing parameters
What registration, fixation and curing parameters were recorded for this run, and how do they compare with the approved settings?
Rub fastness against the standard
What are the rub fastness and hand-feel results for this printed lot, and do they meet the buyer’s standard?
Print run summary
Summarise this print run from the print log and strike-off card: metres printed, rejections, and the reasons recorded.
Screens nearing end of life
Which screens are approaching the end of their recorded life, and which running designs depend on them?
Rejections by cause this week
How much printed fabric was rejected this week, broken down by the cause recorded — registration, colour, smudging or curing?
Strike-offs pending approval
Which strike-offs are pending buyer approval, when were they sent, and which orders are waiting on them?
Paste consumption against norm
Show colour-paste consumption for this design against the norm on file, and explain any variance from the records.
Printing: questions before a demo
Can the agent open our design files or see what the RIP has loaded?
No. The agent reads text, not images, so it cannot open or compare the artwork in a design or print file, and Mavick does not connect to the RIP, the printer or the engraving machine. It works from your digital file registry and screen register, kept as an Excel file, a Google Sheet or a text PDF: file version, date and who signed it off. It quotes the locked version from there, and if a design is not in the registry it says so.
The screen room counts impressions in a paper book. Can the agent use it?
Only once the impressions per screen are in a sheet or file. A photo of a register page, or a PDF made from one, has no text for the agent to read. Once the screen numbers, designs, impressions and life limits are typed into a Google Sheet or an uploaded Excel file, it reads each screen’s count against its limit and lists the ones it finds at or near it, with the designs that use them. It does not count impressions from the machine: the count is whatever your team records.
Will the printing agent see Dyeing’s pre-treatment records?
No. It works only with what is connected to printing, and Mavick keeps each department’s data apart in how it stores and retrieves it. Base fabric dyeing and pre-treatment belong to Dyeing & Processing. So when bulk goes off-shade, it compares paste, curing and the strike-off card from printing’s records, and says the fabric-prep check needs Dyeing’s records. If a preparation report comes with the lot and is uploaded to printing, or shared across the factory, the agent reads that copy.
Can it tell the colour kitchen how much paste to mix?
No. It does not work out paste quantities from a formula, and it does not connect to dosing or mixing stations. It quotes the approved recipe and the norm on file. From an uploaded mixing sheet it adds up what was actually mixed against that norm and shows the rows it used. How much to mix for the next run stays with the colour kitchen in-charge.
Can it update our print log, the screen register or the order in our ERP?
It drafts; an admin decides. If the print log or screen register is a Google Sheet, the agent can prepare a new row or a cell update, such as a screen’s re-engrave date. In Odoo it can draft a production order’s planned start or assignee, or a note on a stock transfer. Each draft waits for an admin, who approves or declines it; nothing changes unless approved. With an ERP other than Odoo it drafts no order changes, only rows in a Google Sheets print log or screen register. Files you upload are read, never rewritten, and it writes no recipes, strike-offs or screen records to any ERP.
Can it check a printed lot’s rub and wash fastness against the buyer’s standard?
Yes, from the test reports. Upload the in-house or third-party report and the buyer’s standard as a text PDF, Word or Excel file. The agent reads the dry and wet rub grades, the wash-fastness result and the method each report names, such as ISO 105-X12 for rubbing or ISO 105-C06 for washing, and sets them against the grade the buyer requires, citing both documents. A scanned report has no text to read. It does not test fabric or judge hand-feel: it quotes what the report records.
Bring Printing. We’ll build it on the call.
Book a 30-minute demo (opens in a new tab)- support@mavick.si
- Demo calendar
- calendly.com/safock/30min (opens in a new tab)